ASPC LFI2130
LFI2130 is recommended for blown film extrusion. This product is suitable for manufacture of heavy duty LDPE film packaging for application like shrink hoods, industrial acks, Carrier bags and liners.
Extruder temperature profile: 185-200°C
Frost line height: 5-7 times die diameter.
Blow Up Ratio: 2-4
Recommended film thickness: 45 to 150 μm.
Please note that, these processing conditions are recommended by producer only for
100% LFI2130 resin (not in the case of blending with any other compatible material),
but because of the many particular factors which are outside our knowledge and
control, and may affect the use of product, no warranty is given.
Supplied in pellet form and can be packaged in 25kg Bags, one ton semi bulk or 17 tons bulk containers.
The above-mentioned material meets the relevant requirements as laid down in:
- Regulation 174/2015 (amending Commission Regulation (EU) No. 10/2011)
- European Pharmacopoeia, paragraph 3.1.5.
- Metals test, standard 71-3
- Halogens, IEC 61249-2-21
- Heavy metals, EC Directive 94/62/EC
- RoHS, 2011/65/EU and 2002/96/EC
- Phthalates, Directive 2005/84/EC
Conveying equipment should be designed to prevent accumulation of fines and dust
particles can, under certain conditions, pose an explosion hazard. We recommend
that the conveying system used:
Be equipped with adequate filters.
Is operated and maintained in such a manner to ensure no leaks develop.
That adequate grounding exists at all times.
We further recommend that good housekeeping will practiced throughout the facility.
All resins should be protected from direct sunlight and/or heat during storage. The
storage location should also be dry, dust free and the ambient temperature should not
exceed 50°C. It is also advisable to process polyethylene resins (in pelletized or
powder from) within 6 months after delivery, this because also excessive aging of
polyethylene can lead to a deterioration in quality. ASPC would not give warranty to
bad storage conditions which may lead to quality deterioration such as color change,
bad smell and inadequate product performance. It is also advisable to process
polyethylene resins (in pelletized or powder form) within 6 months after
delivery, this because also excessive aging of polyethylene can lead to a deterioration
in quality.
Minimal protection to prevent possible mechanical or thermal injury to the eyes.
Fabrication areas should be ventilated to carry away fumes or vapors.
Combustibility
Polyethylene resins will burn when supplied adequate heat and oxygen. They should be handled and stored away
from contact with direct flames and/or other ignition sources .in burning; polyethylene resins contribute high heat
and may generate a dense black smoke. Fires can be extinguished by conventional means with water and mist
preferred. In enclosed areas, fire fighters should be provided with self-contained breathing apparatus.
| Properties | Value (1) | unit | Test method |
| Physical Properties MFI(190 0C /2 .16 Kg ) Density Mechanical properties (2) Impact strength Tear strength (TD) Tear Strength (MD) Yield stress (TD) Yield stress (MD) Tensile Stress at break (TD) Tensile Stress at break (MD) Strain at Break (TD) Strain at Break (MD) Modulus of Elasticity (TD) Modulus of Elasticity (MD) Coefficient of friction Blocking Re-blocking Optical properties (2) Haze Gloss (45 o ) Clarity Additive :Antioxidant |
0.3 921 31 45 20 10 11 24 22 >500 >350 150 140 0.7 <5 20 12 55 50 |
Dg/min Kg/m3 KJ/m KN/m KN/m MPa MPa MPa MPa % % MPa MPa g g % % mV |
ISO 1133 ISO 1183 (A) ISO 7765-2 ISO 6383-2 ISO 6383-2 ISO 527-1/3 ISO 527-1/3 ISO 527-1/3 ISO 527-1/3 ISO 527-1/3 ISO 527-1/3 ISO 527-1/3 ISO 527-1/3 ASTM D 1894 SABTEC method SABTEC method ASTM D 1003A ASTM D 2457 SABTEC method |
Notes:
(1) Typical Values: not to be construed as specifications limits.
(2) Properties are based on 120 μm blown film produced at a melt temperature of
200°C and 3 BUR using 100% LFI2130.
